Implement flowspec validation procedure as described in RFC 8955 sec. 6
and RFC 9117. The Validation procedure enforces that only routers in the
forwarding path for a network can originate flowspec rules for that
network.
The patch adds new mechanism for tracking inter-table dependencies, which
is necessary as the flowspec validation depends on IP routes, and flowspec
rules must be revalidated when best IP routes change.
The validation procedure is disabled by default and requires that
relevant IP table uses trie, as it uses interval queries for subnets.
One of previous commits added error logging of invalid routes. This
also inadvertently caused error logging of route loops, which should
be ignored silently. Fix that.
Most error messages in attribute processing are in rx/decode step and
these use L_REMOTE log class. But there are few that are in tx/export
step and these should use L_ERR log class.
Use tx-specific macro (REJECT()) in tx/export code and rename field
err_withdraw to err_reject in struct bgp_export_state to ensure that
appropriate error reporting macros are called in proper contexts.
Routes from downed protocols stay in rtable (until next rtable prune
cycle ends) and may be even exported to another protocol. In BGP case,
source BGP protocol is examined, although dynamic parts (including
neighbor entries) are already freed. That may lead to crash under some
race conditions. Ensure that freed neighbor entry is not accessed to
avoid this issue.
This is an implementation of draft-walton-bgp-hostname-capability-02.
It is implemented since quite some time for FRR and in datacenter, this
gives a nice output to avoid using IP addresses.
It is disabled by default. The hostname is retrieved from uname(2) and
can be overriden with "hostname" option. The domain name is never set
nor displayed.
Minor changes by committer.
There are three common ways how to encode IPv6 link-local-only next hops:
(:: ll), (ll), and (ll ll). We use the first one but we should accept all
three. The patch fixes handling of the last one.
Thanks to Sebastian Hahn for the bugreport.
The RFC 5575 does not explicitly reject flowspec rules without dst part,
it just requires dst part in validation procedure for feasibility, which
we do not implement anyway. Thus flow without dst prefix is syntactically
valid, but unfeasible (if feasibilty testing is done).
Thanks to Alex D. for the bugreport.
During NLRI parsing of IPv6 Flowspec, dst prefix was not properly
extracted from NLRI, therefore a received flow was stored in a different
position in flowspec routing table, and was not reachable by command
'show route <flow>'.
Add proper prefix part accessors to flowspec code and use them from BGP
NLRI parsing code.
Thanks to Alex D. for the bugreport.
There is an improper check for valid message size, which may lead to
stack overflow and buffer leaks to log when a large message is received.
Thanks to Daniel McCarney for bugreport and analysis.
Instead of having large stack buffer for max amount of AFI/SAFI pairs.
The old code is not correct w.r.t. extendeded option length, as more
AFI/SAFI pairs may fit into the capability option.
If BGP has too many data to send and BIRD is slower than the link, TX is
always possible until all data is sent. This patch limits maximum number
of generated BGP messages in one iteration of TX hook.
When BGP connection is opened, it may happen that rx hook (with remote
OPEN) is called before tx hook (for local OPEN). Therefore, we need to do
internal changes (like setting local_caps) synchronously with OPENSENT
transition and we need to ensure that OPEN is sent before KEEPALIVE.
Allow to specify just 'internal' or 'external' for remote neighbor
instead of specific ASN. In the second case that means BGP peers with
any non-local ASNs are accepted.
This is a major change of how the filters are interpreted. If everything
works how it should, it should not affect you unless you are hacking the
filters themselves.
Anyway, this change should make a huge improvement in the filter performance
as previous benchmarks showed that our major problem lies in the
recursion itself.
There are also some changes in nest and protocols, related mostly to
spreading const declarations throughout the whole BIRD and also to
refactored dynamic attribute definitions. The need of these came up
during the whole work and it is too difficult to split out these
not-so-related changes.
Extend 'next hop keep' and 'next hop self' options to have boolean values
(enabled / disabled) and also values 'ibgp'/ 'ebgp' to restrict it to
routes received from IBGP / EBGP. This allows to have it enabled by
default in some cases, matches features of other implementations, and
allows to handle some strange cases like EBGP border router with 'next
hop self' also doing IBGP route reflecting.
Change default of 'next hop keep' to enabled for route servers, and
'ibgp' for route reflectors.
Update documentation for these options.
The patch implements optional internal import table to a channel and
hooks it to BGP so it can be used as Adj-RIB-In. When enabled, all
received (pre-filtered) routes are stored there and import filters can
be re-evaluated without explicit route refresh. An import table can be
examined using e.g. 'show route import table bgp1.ipv4'.
The new MRT protocol is responsible for periodic RIB table dumps in the
MRT format (RFC 6396). Also the existing code for BGP4MP MRT dumps is
refactored and splitted between BGP to MRT protocols, will be more
integrated into MRT in the future.
Example:
protocol mrt {
table "*";
filename "%N_%F_%T.mrt";
period 60;
}
It is partially based on the old MRT code from Pavel Tvrdik.
We currently cannot assing local labels, but we can still be LSP egress
router. Therefore when we announce labeled route with local next-hop, we
should announce implicit-NULL label instead of rejecting it completely.
RFC 3107 was bit vague with regard to labeled withdrawals, RFC 8277
clarified that. The old code was incompatible with some implementations,
namely with Juniper.
Thanks to Vadim Fedorenko for the original patch.
The patch implements BGP Administrative Shutdown Communication (RFC 8203)
allowing BGP operators to pass messages related to BGP session
administrative shutdown/restart. It handles both transmit and receive of
shutdown messages. Messages are logged and may be displayed by show
protocol all command.
Thanks to Job Snijders for the basic patch.
Covers IPv4/VPNv4 routes with IPv6 next hop (RFC 5549), IPv6 routes with
IPv4 next hop (RFC 4798) and VPNv6 routes with IPv4 next hop (RFC 4659).
Unfortunately it also makes next hop hooks more messy.
Each BGP channel now could have two IGP tables, one for IPv4 next hops,
the other for IPv6 next hops.
Basic support for SAFI 4 and 128 (MPLS labeled IP and VPN) for IPv4 and
IPv6. Should work for route reflector, but does not properly handle
originating routes with next hop self.
Based on patches from Jan Matejka.
